YJS-510 rtv liquid silicone rubber for gypsum mould
Category: Gypsum molding silicone
Publish Time: 2018-08-07 11:06
YJS-510 is a type of soft silicone with hardness Shore A 10.It is widely used for making molds for soaps, candles, gypsum cornice, small crafts and etc.
1. Description
YJS-510 is a type of soft silicone with hardness Shore A 10. It is a kind of two-component materials consisting of a flowable part A which when mixed with the curing agent or hardener,cures at room temperature by a condensation reaction. It is widely used for making molds for soaps, candles, small crafts and etc.
YJS-510 is a type of soft silicone with hardness Shore A 10. It is a kind of two-component materials consisting of a flowable part A which when mixed with the curing agent or hardener,cures at room temperature by a condensation reaction. It is widely used for making molds for soaps, candles, small crafts and etc.
2. Features
-Amazing fluidity and easy to operate
-Complex design available
-Not Oily
-Stable quality, non-toxic and odorless catalyst provided
-Easy de-molding
-Excellent tension and tear strength
-High performance in duplication
-Shrinkage is almost zero (below 0.2)
-Excellent resistance to weather, temperature, aging, acid and aging-proofing.
3. Technical datasheet
-Amazing fluidity and easy to operate
-Complex design available
-Not Oily
-Stable quality, non-toxic and odorless catalyst provided
-Easy de-molding
-Excellent tension and tear strength
-High performance in duplication
-Shrinkage is almost zero (below 0.2)
-Excellent resistance to weather, temperature, aging, acid and aging-proofing.
3. Technical datasheet
Typical general characteristics
|
Inspection Method
|
Value
|
Product data (Catalyzed A+B)
|
YJS-510
|
|
Hardness
|
Shore A
|
10±2
|
Mix Ratio
|
A:B
|
100:2
|
Color
|
/
|
White
|
Pot life
|
25 ℃ (77F)
|
30-40mins
|
Curing time
|
25 ℃ (77F)
|
3-4 hours
|
Mixed viscosity
|
mPa.s
|
15000±2000
|
Tear-strength
|
kg/cm
|
26±2
|
Tensile-strength
|
M.pa
|
≥4.2
|
Elongation
|
%
|
≥530%
|
Shrinkage
|
%
|
≤0.2%
|
4.Using instructions
Step 1: Prepare and clean the prototype.
You must make sure your original molds perfect. fix the original mold on a board , then using some assistant material(like cardpaper) to make a frame for to surround the prototype. The frame is no need ,if we make the mold by brushing way .
Step 2: Take the silicone and catalyst as the ratio 100:2 (silicone:catalyst=100:2) ,mix the silicone rubber and catalyst evenly.
*Notes: Molding silicon rubber is a kind of flowing liquid and it contains two parts. Part A is a kind of flowing liquid and part B is the curing agent. Remember to mix part A and part B evenly, otherwise the silicon rubber will be partly solidified and this will bring troubles for your final operation. What's more, the finished molds will have a short life. All of these will cause a waste of silicon rubber.
Step 3: Vacuum pumping
After mixed the silicone evenly, it is better to release the bubble by Vacuum pumping.
Step 4: Pouring cast or brushing cast
After released the bubble, we can pour/brush the silicone rubber on the prototype
*Notes:Please finished all the stepped within the operation time .If not it will cause cross linking reaction, and no more further steps will be available.So,we have to pay
attention to the pot life and curing time.
5.Appearance
Part A: Silicone rubber is a white liquid
Part B: Catalyst is a non-toxic and odorless liquid, white transparent color.
ATT: We can provide fast/medium/slow catalyst of for hot, warm or cold season.
6.SHELF LIFE:
When stored at or below 32°C (89.6°F) in the original unopened containers, YJS-5 series Silicone Base and its Curing Agents have a usable life of 12 months.
7.Package
Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum.
Curing Agent: 30g/bottle; 1kg/bottle
Contact Us
E-mail: info@sz1j3.com
Tel: +86-0755-85200989
Mobile/WhatsApp: +86 13823512713
Skype: live:gcsilicone1
Address: No. 25, Baolong 1st Road, Nanyue Community, Baolong Street, Longgang District, Shenzhen,china